Varad ULS400 - Scanning LED Under Car Lighting System Bedienungsanleitung PDF herunterladen

WWW.VARAD.COM

In order to provide you with prompt warranty service and technical

support please register your product on line at

www.varad.com/techsupport/register.Be sure to have your product

serial number ready.This can be found on the bottom of the digital

controller.

Send us your photos

We would love to have pictures of your install on our street gallery.

Go to www.varad.com/street-gallery.html for more information.

Warranty

Trouble Shooting

Sy st em does not turn “ON”

Check to see that the ribbon cable from the r emote

controller is fully in serted into the controller.

Check “Ignition Wire”, make sure it is getting constant 12

volts positive when engine is “ON”.

Check fuse. If fuse looks bent or blo wn r eplace with a 5amp

fast acting glass fuse.

Make sure th at ribbon cable from r emote control is not

pinched or damaged.

LED lightbar does not work.

Check to see that cable between LED lightbar and controller

is not damaged.

P lug into another port to verify that it is the LED lightbar.

A Section of m y LED lightbar is not working

P lug LED lightbar in to another port to verify that it is the

LED li ghtbar.

Check to see that all the wir es on the LED lightbar connector

are fully ins erted into the header.

For technical support:

Check website www.varad.com

or email questions to: techsupport@varad.com

• 12 Scanning, 3 Strobing, 3 Comet and 2 Breathing patterns. 3

selectable speeds.

• Solid glow with 4 levels of intensity control.

• Selectable Music Reactor frequencies (40hz, 80hz, 120hz).

• Network of multiple systems.

• Remote control acts as a SCANNERS™ Visual Theft Deterrent

when ignition is turned off.

• Compact digital controller for ease of installation.

• Wired remote control with LED’s that indicates pattern.

• Connectors on all LED lightbars for quick install.

• Low profile tubes (0.5” x 0.7”).

• Waterproof polycarbonate LED lightbars.

• Optional wireless remote control - ULS400WRC.

Features

General

Thank you for purchasing the ULS400 Scanning LED undercar

lighting system from VARAD. To ensure proper use, please read

this manual prior to installation.

The ULS400 demonstrates the innovation and technical abilities

of the engineering team at VARAD. Our latest kit combines superior

functi onality with sleek pro duct styling to put your rid e at the

forefront of the tuner scene. With 4 low profile LED lightbars,

digital control module and a sleek wired hand-he ld controller,

you can command cool scanning patterns, strobing action or just

glow.With our patent pending new system configuration,optimum

color bleed is achieved using our latest high flux 70 degree LED’s.

These new high flux LED’s allow us to use fewer LED’s than those

found in typical applications to provide a more uniform and superior

color blend. If you demand the latest in lighting technology,

VARAD will take you there - Enjoy!.

To prevent fire or shock hazard, do not expose the digital controller

to rain or moisture.

To avoid electrical shock, do not open the digital controller. Refer

servicing to a factory authorized dealer.

Replace the fuse only with the type provided in the fuse holder.

Failure to do so can cause malfunction.

Precautions

All “Slave” sys tems on the network will replicate the “Master”

system in the following way:

Mode 1: Solid.

All networked controllers will change to the master system “ONLY”

after the intensity has been selected.

Mode 2: Patterns/Strobing/Breathing/Comet

All networked controllers will have an initial delay in synchronizing

to the master controller.

Mode 3: Music Reactor.

All networked units will react in sync with the master controller.

To exit set up mode - Push and hold button until

all LED’s turn “OFF”.

Network mode is now “Active”.

Step 4:

Push button once to turn LED no.4 “ON”.Step 3:

Technical Specifications

Patterns: 11 Scanning, 3 Strobe, 2 breathing, 3 Comet

Speed: 3 selectable speeds

Glow : 4 Intensity levels

Music Reactor Frequencies: 40hz, 80hz, 120hz

Network ready for multiple kits

Physical Specifications:

Digital controller:

Height - 0.8”

Width - 4.0”

Length - 3.75”

Current draw - 20 ma to 1.4 amps depending on mode or pattern

Remote Control:

Height: 0.4”

Width: 1.25”

Length: 3.5”

LED LightBar:

Long LED LightBar length is 48.5” +/- 0.5”

Short LED LightBar length is 25” +/- 0.5”

Wires:

Each light bar has 12’ of cable

Electrical specifications:

LED’s:

Orange - ALINGAP, 70ma, 70 degree

Red/Yellow - TS ALINGAP, 70ma, 70 degree

Blue/Green/White/Aqua - INGAN, 50ma, 70 degree

Each ULS400C controller features a built in“network ready” feature.

This feature allows multiple kits to be installed at the same time

on large vehicles such as SUV’s,Limousines, Semi’s,RV’s and Marine

applications. To activate this feature simply connect the white

wire of all digital controllers together during installation and set

up the master as shown below.

Setting up the “Master” controller.

Installation notes!

Only one wired rem ote control needed. The digital controller

with the wired remote controller will be designated“Master”.

Only the “Master” unit requires hook up of the music input wire

(Blue wire).

All controllers must have ground wire, positive wire and ignition

wire connected at the same location.This will ensure best network

communication.

All controllers must have their own fuse. Do not use one fuse for

all systems!

Turn ignition “OFF”

Push and hold button until LED no.1 is “ON”.

(release button after LED turns“ON”).

Step 1:

Step 2:

Networking Multiple Kits

Wiring Schematic

See “Wiring Schematic Continued Page 9”

Front of vehicle

• There are no specific plug

locations for plugging in the LED

light bars.

Install the Digital Controller inside the vehicle. Find a location

that will allow all the wires to the LED lightbars to connect

without binding.The location should be 36”from where you

decide to install the wired remote control.The wired remote

control should be installed in a location within reach of the

driver.

Installation of Controllers

Wiring schematicWiring Schematic Continued

Connect wiring harness as indicated below:

• Red wire - Battery Positive

• Black wire - Negative (ground)

• Yellow wire - Ignition (+12v when ignition is “ON”)

• Blue wire - Positive speaker terminal

• White wire - Network (See “Networking pg 14”)

When all controllers and LED lightbars are installed you can

proceed to plug all connectors into the ULS400C controller.

Proceed to the “Operation of ULS400” section.

Visually inspect underneath your vehicle to determine a suitable

location for mounting each LED lightbar. Hold the LED lightbar

up in the prospective mounting location to verify that it will not

interfere with existing parts under the vehicle.For the 48.5”

lightbars it is important that the wire leads face the same

direction (front or rear) to ensure symmetry of the Scanning

patterns.When you have found a suitable location, begin to

install the mounting clamps. There are 4 clamps for each side

lightbar and 2 for each front and rear lightbar. Space each clamp

approximately 1 foot between each other. It is important to

install all mounting clamps in a straight line. It helps to use a

reference point on the chassis such as the pinch weld seam, etc.

Mark each drilling point and pre-drill each hole with a 1/8” drill

bit. Install all clamps facing the same direc tion. Now hold the

lightbar up and install a tie strap through the clamp at each

mounting point.Trim excess tie strap material. Repeat the

process for each lightbar.

Installation of LED lightbars

Required tools

• Wire stripper

• Wire cutter

• Assorted drill bits

• Cordless drill

• Screwdriver

Power Harness

Wired Remote Control

Optional Wireless Remote Controller (ULX300WRC)

LED Lightbars

ULS400C Digital Controller Description

Mode Operation flow chart

“Push and Hold”

to change modes

Release button when mode

LED is illuminated

OFF

MODE 1

GLOW

MODE 2

SCANNING

MODE 3

MUSIC REACTOR

No Illuminated LED’s

LED 1 “ON”

LED 2 “ON” momentarily

LED 3 “ON”

ULS400

SCANNING

LED UNDERCAR KIT

Installation Manual

ULS400RC Remote Control Description

Mode / Pattern select button

Mode 3 LED indicator

Mode 2 LED indicator

Mode 1 LED indicator

The remote control also indicates the scanning pattern with each

of the 5 LED’s. Each LED on the remote control corresponds to a

section of the LED lightbar.

The remote control will flash a Scanning pattern when ignition is

turned off. The Scanning pattern cannot be changed.

ULS400RC - Visual Theft Deterrent

Operation of ULS400

The ULS400 is operated with a single button remote control. All

features can be controlled by three types of button operations:

• “Push and Hold” (greater than 1 second) to change modes.

• “Push and release” (momentary) to change features in

selected mode.

• “Double click” to change speeds (Mode 2 only)

For example:

To turn system “ON”

Push and hold button until Mode 1 LED is active.The system will

power up and go into Mode 1 (Solid Glow).The default intensity

is level 4 (Maximum brightness). Each momentary push of the

button will change the intensity level. Refer to “Mode Operation

Flow Chart” for more details.

There are three modes of operation:

Mode 1 - Solid Glow

Mode 2 - Scanning patterns/strobe/Breathing/Comet

Mode 3 - Music Reactor

Refer to “Mode Features”on page 13 for details on features for

each mode.

Turning system“OFF”

To turn the system “off”quickly, push and hold button until all

lights on the remote control turn “off”.This will take a few

seconds only.

Parts list

ULS400C - Digital controller.

ULS400RC - Wired remote control.

Two 48.5” LED lightbars.

Two 25” LED lightbars.

Power harness.

Self tapping screws, 12pcs.

Tie straps, 12pcs.

Mounting clamps, 12pcs.

Installation manual.

LED Lightbars

ULS400C - Digital controller

Mounting clamp

ULS400RC -Remote control

Items not show to scale

Mode Features

Mode 1 • Solid Glow

Mode 1 features solid lighting of all segments. In this mode

you can select from four different levels of brightness.To

change the brightness level push the button once and

release.The remote control will show up to four LED’s

indicating the intensity level of the LED light bars. One LED’s

is for level 1, two LED’s is for level 2, three LED’s is for level 3

and four LED’s for maximum brightness.

Mode 2 • Scanning/Strobing/Breathing

When in mode 2 you can select the following with each

momentary push of the button. The system will remember

the pattern next time you return to this mode.

To change speed - Double click the button.There are 3

speeds available for most patterns.

• 11 Scanning patterns

• 3 Strobe patterns

• 2 Breathing patterns

• 3 Comet patterns

Mode 3 • Music Reactor

When in mode 3 you can select the following with each

momentary push of the button.

• 40hz (LED no.3 will flash 2 times to confirm)

• 80hz (LED no.3 will flash 3 times to confirm)

• 120hz (LED no.3 will flash 4 times to confirm)

Inhaltsverzeichnis

Seite 1 - ULS400RC -Remote control

WWW.VARAD.COMRegister your productIn order to provide you with prompt warranty service and technicalsupport please register your product on line atwww

Kommentare zu diesen Handbüchern

Keine Kommentare

Varad ULS400 - Scanning LED Under Car Lighting System Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Varad ULS400 - Scanning LED Under Car Lighting System herunter. Varad ULS400 - Scanning LED Under Car Lighting System User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Varad ULS400 - Scanning LED Under Car Lighting System